| THE MG |
|
|
 | | December 24, 2010 - Janel and I took the MG for some last-minute shopping.
It was kind of fun, the car's enough of a "real car" we can do this now. It's definitely quieter and Janel strongly approves of the new interior look.
Unfortunately, in some stop-and-go traffic trying to get in and out of the grocery store, the car got pretty hot. I didn't hear the fans kick in, even though it momentarily got hot enough that both should have been spinning away. All of my other testing has been at higher speeds and cooler temperatures. I'm going to have to look in to this.
It was by far the coolest looking car in the parking lot, though.
entry 522 - tags: cooling | | |  | December 26, 2010 - A (poor) shot of the complete dashboard.
Quite a change from the original look. The overspray on the carpet isn't really noticeable in person, you only see it when it's all lit up with the flash.
There hasn't been any major work on the car in the last few days, I've just been driving it. The defroster got a test on Christmas night when we had to head home after dinner, and it passed. I still need to work on sound levels coming from the back of the car, but a bit more of my silver cladding should help out there. I suspect that this would not be a problem in one of the convertibles, but the coupe body does provide a nice resonance chamber at around 1500 rpm. Still, I've been enjoying it quite a bit so far. The speedo works well and seems to be accurate, the dash lighting is about as good as could be expected and overall the car is working fairly well. The new Bosch H4 headlights I installed put out ridiculous amounts of light, just as I'd hoped.
Just because it's that time of year, I took a look back to see what I was doing around this time in the past. A year ago, I drove the Camaro into the garage for the final time. Two years ago, we decided to disassemble the interior. And this year we used the car to drive to Christmas dinner. I'd call that progress!
entry 523 - tags: interior, testing, looking back | | | December 26, 2010 - I decided it would be a quick and easy thing to check the fans out by just grounding one of the wires on the relay.
I tried it...and nothing. A bit of probing with the test light revealed there was no power at the relays - and a check at the fusebox showed two blown 20A fuses, one for each fan.
Looking at the fan ratings, they're supposed to pull around 13-13.5A. But that's continuous running. I don't have the specs for a startup draw on these particular fans, but one other Spal I've used in the past has a continuous draw of 12.5A and a startup draw of 18A. So it's quite possible that my fuses simply weren't up to the task. The wiring could certainly take it, so I'll just drop in a couple of 25 or 30A fuses and see what happens.
entry 524 - tags: fans, wiring | | |  | December 31, 2010 - I was out of town for a while, but the little brown elves brought me some presents!
While driving the MG and working on the interior, I've been keeping a list of bits and pieces that it needs. The mirror is about the most exciting part - that's an earlier mirror that matches the driver's side one off the parts car. It's much nicer looking than the ones that came on the car, gives better visibility and lets me open the vent window all the way. Seems like an improvement!
The other parts are more prosaic. New wiper blades, a seal for the "fresh air door" on the firewall that I don't think will fully close anyhow, light bulbs, etc. Not exotic, but enough to make the car a bit nicer inside.
There's also that Innovate box. That's a pretty cool toy - more on it later.
entry 525 | | |  | January 3, 2011 - Air time!
I drove the MG to work today. This let me check out some of the new sound proofing and generally play with the car. More importantly, it gave me a chance to put the car in the air and take a good look at the underside from a bit of a distance, not from the distance you get using a creeper and jackstands.
Looks pretty good underneath, actually. The exhaust is very clear in this photo, but you can also see the new structure under the front of the car. The original frame rails (or the reasonable facsimile thereof found in the unibody) are cut off at an angle just aft of the control arms. The big new 2x4 box section runs from the transmission support forward, and everything ahead of those cut frame rails is new. The tape holding the heat shielding to the driver's footwell failed on the way to work, so it's missing here.
It's funny, the engine looks so small from this angle. That oil pan is tucked up behind an impact bar and should be very well protected.
entry 526 - tags: underneath | | |  | January 3, 2011 - Here's the view from the rear.
The tight packaging for the mufflers is pretty evident - in fact, that black mark on the right muffler is the insulation from the fuel level wire before I put some heat shielding on it! The new frame members running forward from the trailing arm mounts aren't very visible, but the arms of the lift are lifting from there.
The inspection did reveal a few things. There are a few wires that need to be wrapped up mostly for appearances sake. That fuel level sender wire is still awfully close. The fuel line and main power line also run pretty close to the exhaust (hard to avoid given the giant X!) and really should have some extra heat shielding just in case. But it's pretty good overall.
One thing did come to my attention. The pinion angle seemed a bit off, with the nose of the diff higher than I think it should be. The alignment shop set it, but either the adjustment shifted because the lock nuts weren't tight - they weren't - or they have a different idea of what it should be. The angles of this setup could very well be the reason I'm getting a bit of vibration in the car. Not a shaking, more of a deep rumble that could be the stiff motor mounts, exhaust noise or drivetrain vibration. So I dropped the nose down a bit and we'll see how it works on the drive home. Not tonight, though - a surprise snowstorm marooned the car at work and I went home in a stock 1992 Miata. Regular readers will remember I did almost exactly the same thing two years ago in the Camaro!
entry 527 - tags: snow, pinion, underneath | | |  | January 3, 2011 - The newest toy.
I picked up an Innovate OT-2 over the holidays. It's an OBD-II scanner with a bit of a difference. It packs a little wireless transmitter that can talk to an iPod Touch or an iPhone, allowing the iPod to display real-time data from the car, datalog it, read codes, give efficiency information or even simulate a dyno run. It's pretty cool stuff. I need to recalibrate my engine computer for the MG's tire diameter instead of the Camaro's so some of the readouts are accurate, but it's nice to be able to monitor the car so closely nd then just slip the screen into my pocket when I'm done.
Not many 1972 MGs can talk to an iPod!
entry 528 - tags: innovate OT-2, ipod | | |  | January 5, 2011 - While I had the car on the lift, I decided to drop it down on to the scales.
After all, it's just about completely done from a mechanical standpoint. There's the bodywork and paint to do, but that's unlikely to add any weight. So we can call this a pretty accurate final weight.
The car has nearly a full tank of gas and even carries a spare tire. So this is a full-on legitimate street weight, not a setup for the lightest possible option. Still, I'm pretty happy. When I first weighed the car a year ago, I estimated 2400 lbs. Looks like I was right!
Check out the balance. 51.9/48.1 front/rear. Even better, perfect corner balancing and side/side distribution. There's no reason for that, I just got lucky. But it's still worth bragging about!
entry 529 - tags: weight | | | January 9, 2011 - A few interesting numbers.
I was looking at various specifications, and came across the original MG ones. Or at least, a reasonable facsimile thereof - it can be hard to find sources for some of this.
Apparently the MGB GT weighs 2443 lbs and has 52% of its weight on the front wheels. The V8 version that appeared in 1973? 2390 lbs - the stock four-cylinder was really heavy. So my car is basically the same weight as the factory V8 job. Of course, it had 137 hp while mine is somewhere around 350-400, depending on the modifications that were made to the engine before I got it.
I was also looking at the hot new 2012 Boss Mustang. It's rated at 440 hp, but weighs as much as the MG and my Seven combined. More eye-opening is the size - it's 35" longer than the MG. Nearly three feet! Wow.
More work to come on the MG soon. I can feel the final bodywork looming. It's going to be a dusty time.
entry 530 - tags: dimensions | | |  | January 14, 2011 - I spent part of the day today talking paint and bodywork with the local paint shop.
Hightower supply has been very helpful to me. I came home with some new primer and a big bucket of body filler to make those fender flares all pretty.
I also want to try some rubber motor mounts in the car. I think some of my noise is vibration coming through the mounts. I put some competition motor mounts on Janel's street Miata and got a similar noise. Now, the mounts I used were generic small block Chevy (pre-LS1) mounts from Energy Suspension. I went to NAPA, opened up the Big Book Of Motor Mounts, and spotted this on the first page. I don't know what the application is - probably every V8 from General Motors from 1960 to 1997 - but I think that's it. I just hope the softer mounts don't let the exhaust and other bits and pieces lean up against each other.
entry 531 - tags: motor mounts, bodywork, paint | | |  | January 14, 2011 - Big news - I'm going to the Targa Newfoundland.
Long-time readers may remember that the Targa caused a hiatus in MG development in 2008. Actually, it was during that pause that I decided to go with the LS1 instead of a Ford 302. But anyhow...we're going back.
You can read all the details on the Targa Miata website. It's actually going to get an engine swap, and the subject of the swap should be pretty familiar. Yup, there's an LS engine going in. Not an LS1, but the L33 I'd been considering years ago. The power/weight ratio will actually be very similar to that of the MG, so I guess we could call this little car practice. What I learned building the Miata in the first place helped the MG, and I've picked up a few things with the MG that will make the V8 Miata work better. Everybody wins!
However, I need your help. We need more funding in order to make this a reality. If you're enjoying the build of the MG and my other projects, please consider helping out a bit. Of course, the build and the race will be documented just like this one has been. Details
entry 532 - tags: targa newfoundland, help | | | January 16, 2011 - I swapped the motor mounts out today.
It was a reasonably easy job, probably much easier than most production cars. It'll be even easier next time, since I turned one of the long bolts around so it runs back to front instead of front to back. Seems simple, but next time I won't have to pull the alternator...
I believe it was a success. The car doesn't boom and vibrate as much. It's still vocal but you can tell the noise is coming from the back of the car through the exhaust pipes instead of simply through the chassis. A bit more work with sound deadening in the back half of the car and I think it'll be quite good.
entry 533 - tags: motor mounts | | |  | January 18, 2011 - The flares look pretty good, but there's one line that bothers me.
The trailing edge of the front fenders doesn't blend into the body as well as I'd like. It's not something you'd notice unless you spend hours looking at the car and working on small areas of it, but they don't look factory.
I do have a couple of stubs that were cut off the leading edge of these flares as I was building them. They have a better shape.
entry 534 - tags: body, fender, flares | | |  | January 18, 2011 - Much better!
The flares now blend into the body perfectly, even following a curve at the bottom of the fender when viewed from the side. I'm really happy with how this turned out, they're even better in person.
It's unlikely anyone would have noticed unless I'd pointed it out, but now I'm satisfied.
entry 535 - tags: body, fender, flares | | |  | January 18, 2011 - Since I had the welder out and the front wheels off, the obvious thing to do is to add a front sway bar.
The car needs more roll stiffness, and I've been looking at how to add a front bar for a while. Of course, I'm trying to use a Miata part because I have a huge collection of them.
I built a couple of plates with studs in them and welded that to the bottom of the frame rail. I considered simply installing some rivnuts, but the sway bar mounts see quite a bit of load and I can see myself ripping them out of the frame. So I have a nice solid mount instead.
The geometry would have worked better if the bar was on top of the frame rail instead of underneath, but the packaging would simply not allow that. Even if I could cut a big enough hole in the panel above the rail, there isn't enough room for the bar to go between the engine and radiator. We'll see how it works. On a short drive, the car did feel more settled. Too much traffic to try out the handling balance. I'm still dialing in the spring rates so I'm not sure exactly what the sway bar sizes will be yet. This one's off a 2004 Mazdaspeed turbo Miata. Why? Because that's what I had on hand! If I want a softer bar, I can use a non-turbo version. If I want an adjustable bar, I can use one of the Flyin' Miata ones.
And yes, I have an idea for a rear bar. We'll see if it will package.
entry 536 - tags: sway bar, handling | | |  | January 18, 2011 - The sway bar has an upward angle to it due to the bar placement.
The stock end link - the black one - made this as bad as it could be. So I decided to go with a shorter unit. I have boxes full of old Miata suspension pieces, of course, and the heim-jointed end link in the middle is from the "end link" box. Seriously, I have a box for Miata end links. I also have a box for bumpstops, a wall full of springs, a cord of sway bars, random steering column parts, etc. And at least three boxes of wires. But I digress.
The unmodified heim-jointed link was still too long. So I cut it down, as you can see on the right. There's still a lot of thread engagement so strength is not a problem, but I've made the angle of the bar much better.
It's not the only suspension work I did today. When I was first doing the suspension work on the car, I didn't pay too much attention to the control arms and suspension uprights I used. All the important dimensions are the same. But in my fevered excitement to assemble the car for the First Drive, I left those parts on the car. And that was a problem.
Mazda tweaked the Miata's suspension in 1999. The control arms got beefed up a bit, although the dimensions were basically unchanged. The one change was on the taper of the upper ball joint. The steering knuckle/upright was also very similar, with the steering arm moved up by 7mm and the appropriate taper on the seat for the upper ball joint.
Well, when I looked at what was on the car, I realized that I had the new design upper control arm on one side, but the older steering knuckle. On the other, I had the older parts. This is less than ideal, so I swapped everything out for the newer designs. It was actually a pretty quick job, the guy who built this car was careful to leave enough room to do things like remove suspension bolts. Whew!
entry 537 - tags: suspension, sway bar, end links | | |  | January 18, 2011 - Time to play with tires.
When Janel drove the car on Saturday to see how the various modifications were improving things, she discovered quite quickly that the existing tires were poor. A serious liability, actually. The car's like a loaded gun, with an extreme power/weight ratio and some pretty poor tires. That's the current tire on the left - it's the Falken Azenis RT215. The 215 was discontinued years ago, and while this tire appears to have lots of tread it's actually been heat-cycled to death so it's a little black rock. They hold air, that's their biggest redeeming factor.
The middle tire is a Toyo RA-1, a race tire that can be run on the street. It was pulled off my Seven, which is sitting in the trailer. It's mounted to the same wheel as my Falkens, but is a slightly wider 205 instead of the previous 195.
The right tire is another RA-1 with a little more wear. That's off the Targa Miata. These tires actually last an amazingly long time for a race tire. I pulled it out because it's mounted on a 15" wheel with a different offset, and I wanted to see how it would fit. Also, it was in my way.
entry 538 - tags: tires | | |  | January 18, 2011 - Here are the 14 inch RA-1s installed.
The left rear is the most problematic tire, and it's not quite tucked into place here. The others are fine, with a perfect fit up front. Really, I should have made that rear axle about 1-2" narrower so I could run bigger tires in the back. That may be a future project. For the time being, I want to see how this setup works, as it's a simple bolt-on that doesn't cost a cent.
On the street, the car is far better. It'll still overwhelm the tires, but only under real duress. I'm not sure it's considered socially acceptable to light the tires up all the way through second gear, but it's in the name of Science!
A nice side effect is that the ride has improved considerably. The Falken Azenis has a sidewall that is slightly stiffer than concrete. The RA-1 has a stiff sidewall as well, but it will flex. So I'm quite happy with this.
entry 539 - tags: tires | | |  | January 23, 2011 - During construction, Janel often referred to the MG as her little grocery getter.
And you know what? We're actually using it for grocery runs. She's pretty happy with how it's evolving, between the better/more compliant tires and the sway bar it feels much better planted and less skittish. She also really likes the current suspension compliance.
I've known since I put them on that the current springs weren't long enough - they coil bind before full compression. And I suspect that's actually happening once in a while. So I swapped in a set of 10" springs with a 250 lb rate instead of the 8" 225s that were in there. Why the rate change? Because that's what I have! I'll see what change this makes to the dynamics, and then order some springs of the appropriate rate and length. I've said this before, but it's so easy to change the springs on this car!
entry 540 - tags: suspension | | |  | January 26, 2011 - One last job before I start in with the body filler.
I've decided to remove the side marker lights from the car so it looks like the earliest GTs. I've been driving around with black duct tape covering the holes, but something more permanent is required. Step one, clean up the edge of the holes.
entry 541 - tags: bodywork | | |
|
THE DIARY