| THE MG |
|
|
 | |  | April 25, 2008 - While I'm painting things and I have the wheels off, it's time to take care of these teal wheelwells as well.
I used a different black for this - a satin color. After all, they're not supposed to be shiny. Just dark.
Note the tube shock conversion in the front. That was a surprise!
entry 45 - tags: paint | | |  | April 25, 2008 - More painting!
This time, the rear brake drums. They were ugly and rusty and very obvious behind the new wheels. So a shot of satin Rustoleum and we're good. You might notice that this is three different types of black paint so far. I used four, but I forget what the other was for! Oh right, the cover for the pedals.
So, how did the brakes turn out? Well, it took a bit of cleverness to get them bled properly with the dry master, but once we got a bit of fluid moving through they pumped up nicely. So it looks as if my brake master was a success, at least in the short term.
entry 46 - tags: paint, brakes | | |  | April 25, 2008 - I gave the car an oil change to get rid of the 6-year-old oil in the sump.
The oil filter definitely did not want to come off, but eventually succumbed to a screwdriver hammered through. Crude but effective. I went to drain the oil cooler and - yuk.
So the cooler got cleaned (lots of brake cleaner did the job) and cleaned again. I also discovered that it had been mounted with a couple of sheetmetal screws run through the tapped holes in the body. Oh, and mounted crooked. Nothing but the best! So I ran a tap down the four mounting holes, got four matching bolts and installed it properly. All the holes lined up perfectly - there was just a real hack working on this car at some point.
entry 47 - tags: engine | | |  | April 25, 2008 - While underneath the car to change the oil, I discovered the state of the sway (or anti-roll) bar.
Looks as if it was used to drag the car on to a tow truck or something, a long time ago. Oh well, that's an easy fix. I was going to change the bushings anyhow.
entry 48 - tags: suspension | | |  | April 26, 2008 - One of the steering boots was broken, so it got replaced.
Easy enough, although the "precision engineered" replacement from NAPA (it said so on the box!) was anything but. It was a bit of a fight to get the undersized small end over the surprisingly hefty tie rod, but I won. I always win. It's just depends how badly the car has to lose.
entry 49 - tags: steering, suspension | | |  | April 26, 2008 - Time to change the shackles while the car's up in the air.
On top, one of the monster ones the car came with. On the bottom, a stock GT shackle. It's about 2.5" center to center, by the way.
Interesting note - the droop of the suspension doesn't seem to have changed with the new shackles. I suppose that's because it's basically limited by the shock. But it sure compresses a whole lot further. The car sits much more level and the rear wheels are nicely tucked into the wheel wells.
entry 50 - tags: suspension | | |  | April 27, 2008 - With the new shackles on the rear, the car sits very close to level.
I haven't checked with a tape measure yet, but it looks right. With the rear wheels tucked into the wells, it's obvious that there isn't room for a massive spacer to move them outboard. It looks much better than it did lifted anyhow.
One thing that's apparent is that something's not right with the rear suspension. It's rock solid, with almost no give at all. I'd swear it was sitting on the bump stops but inspection shows that is not the case. It's not seized, as there's definitely movement when I lift the car. But when I push on a fender I get almost no deflection. I wonder if the aftermarket tube shocks are too long and are bottoming out internally? I'll pull apart a few components and see what I can figure out.
The new grille is fitted, although not yet permanently. The bumper overriders make a big difference visually, so they're probably going to stay. It sure looks a lot better than it did when it arrived! The car's coming together visually pretty well.
entry 51 - tags: suspension, wheels, grille, styling | | |  | April 27, 2008 - The older badge looks great in the sunlight.
There's a depth to it that just didn't exist in the later one. Or any other badge that you see on new cars, actually.
entry 52 - tags: badges | | |  | April 27, 2008 - Time for that all-important first drive!
This is always a big moment in resurrecting an old car. With Basil, it was a late-night run around the block at night with no brakes. Hopefully this one will be a little less exciting.
First off, the car's a bit of a slow starter when cold. I just haven't learned the magic ritual yet. Still, it does eventually roar into life. Yes, roar. There are more holes in the exhaust!
The clutch feels good and the gearchange is really nice. The steering feels good underway, although there's a bit of internal friction. It's as if someone overtightened it to get rid of some play. I'll check that out. The stiff (solid might be a better term) rear suspension certainly affects the experience though. I never knew there were so many bumps on my street!
The brakes have a solid pedal, but need a very strong push. There's probably a bit of rust on the pads, and I think it was getting better. Still, we were mostly cruising along and didn't spend much time on the brakes. I'll bed them in and see if that helps.
The engine seems healthy but the carbs probably need tuning, as the idle never drops down below about 1100. There's also a flat spot on rapid tip-in. Not a big deal, just a bit of fettling required. Oil pressure is strong and all of the gauges work with the exception of the engine temperature.
So, all good then? Well, not quite. The car's spitting out radiator fluid. And it looks foamy. Uhoh. The oil looked fine when I drained it, but either the stock radiator cap is completely trashed (possible) or something's pressurizing the cooling system. I haven't investigated this fully yet. It could be a head gasket, although there's no smoke. Further checking will tell the tale.
On top of that, there are also the usual oddities. The turn signal/high beam stalk is stuck on high beam. There are some weird lights stuck on and others that don't work, so I have to disconnect the battery whenever it's not running. But that's okay, that's part of the fun.
In other words, it's a basically decent little car. It has a list of things that need to be sorted out, but it's all doable and at a good level of difficulty.
entry 53 - tags: driving, brakes, suspension | | |  | April 29, 2008 - The mystery of the terrible ride has been solved.
In several ways, actually. I had a suspicion that the shocks might be involved, as they were the most likely candidate for restricting any bump travel. So I lifted the rear of the car up to have a look and whaddya know, one side didn't drop at all. I supported the spring, loosened off the shock and this fell out. It's jammed at full compression. So not only was it preventing the suspension from compressing at all - due to the way it was mounted - but it also was preventing it from moving. So, problem 1 solved.
But there are remaining problems. The shock was fully compressed at ride height, with several inches to go before contacting the bumpstop. Reading the tube shock conversion article in the MG Experience library, I discovered that the lower shock mount was installed upside down. This was probably a good idea given the jacked up ride height originally, but back at normal heights it compressed the shock too much. So, there's a solution then.
Ah, but not so fast. The shocks are a Monroe-Matic Plus 33076, which according to the MG Experience article is the standard Moss shock and is well known for a terrible ride. So I can probably improve on it regardless. The article discussed rooting through parts book and gives a couple of other options. But I can do better! A visit to the Monroe website unearthed a PDF document with all of the mount types, extended lengths, compressed lengths and other good info. A bit of messing around and I turned it into a spreadsheet. So now I can search quickly and easily! I can't tell anything about the damping of the shock, but once I've picked out a few that have more travel than the originals, I'll look up their applications and see what that tells me. Or I'll call Monroe. This is going to be fun.
entry 54 - tags: suspension | | | April 30, 2008 - The shocks have been selected.
Most of my early selections turned out to be for various one-ton vans, with an expected stiff damping. The Mitsubishi Cordia of the late 80's has some shocks that have been used in the past, and they looked to be a good match. There's also a Corvette application that looks interesting, but the 1986 Corvette wasn't exactly known for ride quality!
So, with the application nailed down, I was able to choose between a KYB, Monroe-Matic or a Monroe Sensa-Trac. I went for the Monroe-Matic, as I'd heard the Sensa-Trac shocks have some ride quality issues that may be related to internal gas pressure. The cheaper -Matics are probably not damped quite as aggressively. And they're only $17 each, so what the heck. The total bill was $40 shipped. If they don't work, I'm willing to accept that and chalk it up to experimentation.
The fronts use the same size of shock and I considered picking up a set of four, but I'll put that off until later.
entry 55 - tags: suspension | | |  | May 21, 2008 - The new vs the old shocks.
The new vs the old shocks.
entry 56 - tags: suspension | | |  | May 21, 2008 - First step towards installing the shocks - cut down the bushing.
I cut it a bit too far - a touch longer would have worked better with the bolt length. Nothing an extra washer couldn't fix though.
entry 57 - tags: suspension | | |  | May 21, 2008 - Step two - drill out the bushings.
They're sized for 12mm metric bolts, but the MG doesn't speak metric. A bit of time with a 1/2" drill, problem solved.
entry 58 - tags: suspension | | |  | May 21, 2008 - Either a really stupid idea or a stroke of genius.
The holes in the lower shock mount can get ovaled out and I was seeing the first signs of this. The threads on the bolt were getting damaged as well as doing damage.
So I welded in a clevis pin. It's a nice tight fit in the resized lower bushing so there's no slop, and being welded into place means it's not going to move. Plus it means I can pull out a pin and easily remove the shock. I can hear the purists crying.
entry 59 - tags: suspension | | |  | May 21, 2008 - It's about time.
I've been waiting for this manual for over a month. Now I can sort out the weird wiring bugs. British manuals are really good.
entry 60 | | | June 7, 2008 - It's been pointed out that I never actually updated the results of the shock swap.
Well, the car bounces. That's about as far as I've made it. A few other projects got in the way so the GT went to sleep for a while. Until the Targa Newfoundland car is done with the race, the MG will always be a lower priority.
I did spend some time this weekend at an MG event, though. I was a little busy playing rally driver, but I did get the chance to check out a few nicely finished cars. The grille was well chosen, I think, and a well-finished black dash looks great. So we're on track there.
entry 61 - tags: suspension | | | October 26, 2008 - The Targa Newfoundland is over.
It was a lot of work getting the Targa Miata built, tested and out to Newfoundland and back. But that's done. And while some post-race analysis continues, it's time to turn my attentions back to the MG. This site is about to come back to life, as is the little black coupe.
entry 62 | | |  | October 31, 2008 - A new plan.
The original intent was to install a Ford 302 into the MG, as it's cheap and readily available. However, that was before I got mixed up with transplanting an LS1 into a Miata. I fell in love with not only the performance, but also the packaging and the (relatively) light weight of the engine. So I've switched plans. It's going to be an LS1.
entry 63 - tags: engine choice, planning | | |  | October 31, 2008 - Sharp eyes will notice the giant "LS2" on the last engine.
Okay, so I cheated on the picture. And here's the engine I'm really considering. It's marketed as the "Vortec 5300" and it's found in late model Chevy Silverado trucks. But in the 1500 extended cab 4wd versions, it's a special high output version called the L33. Unlike the usual truck motors, it has an aluminum block so it's a lot lighter.
It's also taller, but the LS1/LS6 intake manifold and oil pan should bolt right on. Hopefully it won't be too big a deal to drop the alternator somewhat as well. It's a 5.3 versus the 5.7 of the LS1, and that's simply due to a smaller bore. With the right parts bolted on, it'll basically end up a slightly smaller version of the LS1, and all the same hop-up parts will fit. LS6 cam, perhaps?
But the big reason is that they're a lot more affordable. LS1s are well known and are expensive. Truck motors are not sought after by most enthusiasts. I've been able - without trying too hard - to find a 16,000 mile example for under $1000 shipped. I'm sure I can do better. I'll still have to buy a few parts to make it work, but it'll come in well under the price for an LS1. And with 335 lb-ft and 310 hp, it's not going to be a slouch.
entry 64 - tags: engine choice, planning | | |
|
THE DIARY