| THE MG |
|
|
 | |  | January 28, 2009 - The next step is the steering rack mounts.
To behind, a fair bit of careful measurement. I want to try to minimize bumpsteer, and the best way to do that is to start with the factory Mazda location and then work from there once the suspension is assembled. I duplicated the factory brackets using a piece of 1x3 rectangular steel. A plate on the bottom will provide some lateral strength.
entry 157 - tags: steering, frame | | |  | January 28, 2009 - That 1x3 steel (actually, I think it's 1x2 when I think about it) I used for the steering rack mounts is not new steel.
Far from it - I have some very heavily overbuilt railings that were pulled out of a building under renovation. They live out in the backyard and I chop off a bit when I need it. A bit of quality time under the wire wheel on the grinder and it looks new and ready to weld.
entry 158 - tags: tips | | |  | February 1, 2009 - Time to mount the steering rack, umm, mounts.
I'm still just tacking everything in place, but it's almost time to commit. I did chop a bit of extra frame rail off the sides to clear the rack itself, this was always part of the plan - I figured it was much easier to make them shorter than longer.
entry 159 - tags: steering, frame | | |  | February 1, 2009 - This cut in the steering crossmember was required to clear the pinion housing on the rack.
It's a bit ugly, these were the chops made to get the clearance I needed.
entry 160 - tags: steering, frame | | |  | February 1, 2009 - Once the final clearance was sorted out, I squared off the cut.
Chop chop!
entry 161 - tags: steering, frame | | |  | February 1, 2009 - A small piece of steel was welded in to close up the cut.
It's actually a spare piece of frame rail, the sizing was perfect. Voila, clearance! Once it's welded in completely, I'll clean up the edges with a grinder so it sits flush with the rail.
The steering crossmember could have been smaller, but I wanted the 2x3 tube to give me lots of twisting stiffness for the front of the frame (more than I'd get with a round tube) and to give me a nice flat surface to weld bracing to. Ideally, it should have been 2x2 for packaging purposes so I wouldn't have to do things like this. But that's okay, I think this will end up better overall.
entry 162 - tags: steering, frame | | |  | February 1, 2009 - I borrowed a T56 for some test fitting.
It's a brand new shiny one that should be identical to mine other than the aftermarket shifter. Oh, and a decade of grime! I'm keeping the Camaro together as long as possible.
It's a big boy and weighs about 140 lbs. Quite a contrast from the stock unit, and I'm a bit concerned about fit. But I have a welder!
entry 163 - tags: transmission, Camaro | | |  | February 1, 2009 - Here's the transmission sitting in the correct location.
Correct in two dimensions, anyhow. I pulled the bellhousing off because it's much easier to bolt that part to the engine for clearance testing.
Some quick tape measure work tells me that the T56 should fit much, much better than I'd feared. I haven't lifted it up into the car yet (I need to work out a stable way to support it while being able to lift and move it around), but it appears that it should fit into the stock tunnel as if the car was shrinkwrapped around it. Amazing. There's even a crossmember that I think is in the perfect place to support the rear.
entry 164 - tags: transmission, fitment | | |  | February 1, 2009 - The plastic engine is back in the car.
I clamped a piece of plywood to the bottom of the framerails to ensure the bottom of the engine will not protrude below. And it's looking pretty good. It needs to come back 1.5" from the current position to put the shifter in the correct location, which will place the right head almost up against the leading edge of the footwell. I can make a little more room there if need be.
On the driver's side, the head sits slightly forward so there's more clearance there. But it does hit this protrusion at the bottom of the footwell. A bit of poking around revealed an odd thing - there's a significant amount of footwell in front of the gas pedal at WOT. Space you simply can't use. Is it left over from RHD versions of the car? That useless space is exactly where I need more room in the engine bay, so this is working out nicely. So nicely, in fact, that it appears very little work will be needed to stuff this giant drivetrain in place. Work beyond rebuilding the frame from the firewall forward, of course. But passenger compartment intrusion will be minimized. Amazing.
entry 165 - tags: footwell, clearance, engine | | |  | February 2, 2009 - Time to get out the sawzall, let's get the engine fitted.
This is the passenger's side footwell. This big handy dent is almost perfect. In fact, on initial test-fitting, this side of the car appears to have been factory modified for my needs.
entry 166 - tags: firewall, fitment | | |  | February 2, 2009 - The driver's side is not as good.
Notice how much further the footwell extends inboard from the frame rail. But all of this space is useless - the gas pedal visible in the cut is at full throttle. So, I shall reclaim this space from the interior for the engine.
entry 167 - tags: firewall, fitment | | |  | February 2, 2009 - Remember the steering crossmember that really should have been 2x2?
Well, it's getting closer. To ensure as much oil pan clearance as possible, I had to take a chunk out. Right about an inch at the back and nothing at the front.
entry 168 - tags: steering, frame, clearance | | |  | February 2, 2009 - After a bit of finagling, the transmission is in place.
Sort of. It's sitting about 1" to 1.5" too low and pressed up against the top of the transmission tunnel. Some more surgery may be required - but the fact that I'm this close without making any modifications is astounding. There's one doodad just below the shifter (pardon the technical terminology) that will require a small hammered dent in the tunnel to allow the shifter to be centered in the hole.
However, a test fit of the hood with the engine in place tells me that I'm either going to have to modify the hood or lower the engine. I've been testing the fit with the oil pan level with the frame rails, 5" off the ground. Possibly more, actually, when I review my notes. They show the rails at 5.75" high, although I think that was with the original wheel size. Regardless, I have lots of clearance. I'm tempted to drop the whole thing by 1" to improve clearances everywhere. I'd put a crossmember in front of the pan to protect it. A quick check with a tape measure shows 4" of clearance on one of the Miatas in the garage, so 4" is certainly streetable.
entry 169 - tags: fitment, transmission | | |  | February 2, 2009 - Here's the current shifter location.
It's offset slightly to one side due to the aforementioned doodad but the longitudinal placement is pretty much perfect.
entry 170 - tags: transmission, fitment | | |  | February 6, 2009 - It's in!
The entire drivetrain is in place. There are jacks and clamps and various cheating involved, but I've found my final location. The engine is down not quite an inch from where I had it before, mostly to accommodate the transmission and tunnel. The problem I had with the hood not closing before? It was the hood prop hitting the top of one of my new suspension towers - you can see how it's been cut down on the right side compared to the left. But still, it makes for a better location.
entry 171 - tags: fitment | | |  | February 6, 2009 - And here's the final shifter location.
Looks perfect. You can see the square hole I had to cut in the top of the transmission tunnel to make space for the trans - the tunnel has a low point while the transmission does not. Sorry, make that the tunnel had a low point...
The "doodad" I mentioned before is a reverse lockout solenoid. Above 5 mph, the solenoid prevents you from hitting reverse. There's some logic to that, but it's a hassle for me. It could easily be removed completely but given the tight shift pattern of a T56, that's not the most intelligent solution.
On Elvis, we pulled the solenoid out and tweaked the spring tension in the lockout. This negated the need to run wires to the solenoid, but it still left things a bit on the bulky side for me. I'm going to see if I can manage to design a replacement that fits flush to the side of the transmission. It looks plausible.
entry 172 - tags: transmission, fitment, reverse | | |  | February 8, 2009 - A view of the driver's side motor mount.
Yeah, it's close to the steering column. I might be able to make it work with some artfully curled tubes - or I'm wondering if I can use the extra pair of bosses on the block and support this side of the engine a bit further back.
I did what is hopefully the final cutting of the tunnel today and welded the frame rails in fully. It's not easy welding 1/8" steel to thin floorboards from below without burning through. It's not pretty work, but it'll hold.
entry 173 - tags: mounts, fitment | | |  | February 17, 2009 - Not much work on the car of late.
I'm thinking that I want the full engine with all accessories before I go any further with motor mounts and the like, and that means I need to kill the Camaro. So I'm starting by making storage arrangements for at least one car while I do the work, to ensure I have space in the garage. I may shift my attention to the rear of the car first and get that sorted out, simply to postpone the chaos.
In other news, I brought an LS1 Miata home last night. No, I don't get to keep it! It's been fitted with a big nasty cam and makes a really fun noise. As an added bonus, it also has north of 400 hp. Janel got all giggly when she fired it up in the garage. Too bad we're still breaking in the rear end, so I can't unleash the hounds on this thing. Yes, this requires some self-control.
But I did learn something. It has a modified reverse lockout. The solenoid has been disabled and a different spring inserted. Even when being careful, I bounced off reverse twice while aiming for 5th. Most times I hit the desired gear just fine, but I wasn't too excited about it. So the plan is now to retain the reverse lockout in fully functional form. I'll just have to reshape the transmission tunnel. It's hammer time!
entry 174 - tags: transmission, Miata, Camaro | | | March 29, 2009 - There haven't been any updates for the past month, I know.
That's because I've been working on other things - the Targa Miata went to Laguna Seca for a two-day track event and my editor feels I should be working on my new book instead of hacking up an old MG. So I've been concentrating on that.
I did pick up a new set of motor mounts, though. They'll give me a little more clearance for the steering column. Not a lot, but hopefully enough. I'm also getting concerned about clearance between the alternator and the steering rack pinion. I know there are a number of accessory mounting options for the LS engines (thank you Car Craft for a well-timed article there) but I'd prefer to maintain the Camaro setup because, well, I have one.
In other news, there's a Austin Healey Sprite in the garage right now. I've been tasked with making the freshly built 1275 engine run. Part of my payment for that is an MGB GT body. Hopefully it'll provide a few useful bits and pieces to help restore Janel's.
So, there's not going to be much work on the MG for a little while yet. I really need to be working on that book!
entry 175 - tags: mounts, fitment | | |  | April 27, 2009 - Happy birthday to me!
I know, there hasn't been any progress on the MG in a long time. I've been working hard on the book instead, to the relief of my editor. But Janel is starting to think I should be spending a bit of time on her little black car - and to help motivate me, she gave me a bead blasting cabinet for my birthday. It's going to make working on 37-year-old MG parts, 15-year-old Miata parts and 11-year-old Camaro parts much nicer.
entry 176 | | |
|
THE DIARY